Safe-Home.com

Healthier Living | Child Safety | Eco Friendly Tips

Sliding Door Lock and Sliding Window Lock for Security and Child Safety

by Barbara 2. January 2012 10:42

Question about how to install a sliding door lock on my interior closet doors, my exterior slider windows and my patio sliding door.

Q: "I do not want to install window guards on my windows but I do want to get some ventilation during the winter months here in Florida. We are on the Atlantic side and the breezes are great right now (January). I am concerned about security on the patio door. and downstairs windows. For the upstairs windows, I am concerned more about child safety when grandkids visit. What do you suggest? Thanks. Julie."

Answer: The Cardinal Gates Patio Door Lock comes only in white. the Patio Door Guardian allows you to lock the door with a 3" gap for ventilation. Use on right and left handed sliding doors. Recognized as "one of the best new child safety products" by the National Safe Kids Campaign in Washington, D.C., the Patio Door Guardian works double duty as both a security device and as a childproofing lock.  This unit has a 2 position spring loaded lock with a left and right stop. The keeper plates allows for a 3 inch ventilation gap without minimizing security. This fits most sliding doors and most windows that are vinyl, aluminum or wood. The questions and answers below should help you make your decision.

A new option for sliding doors is the Cardinal Gate Lock-N-Block Sliding Door Gate This gate requires some minor assembly.

Assembly Instructions

  • Choose appropriate screw-in clamps for your door. Screw clamps into gate. These clips will fasten to your open sliding glass door.
  • Screw the stabilized pads into the opposite side of gate. These fit into C-channel of the door frame.
  • Attach gate to open door with clamps, fitting gate into door jamb. Close door to lock in gate.
  • Screw door stop to sliding track to secure sliding door.

Gate Operation:

  • Push red safety button and lift handle 90 degrees upward.
  • Pull gate to open.
  • Close gate and lower handle back to original position.
  • Gate will click when locked.

Gate Dimensions :

  • Gate width is 24"
  • Height 30.5"
  • Thickness: 1"
  • Bar Spacing 1 7/8"
  • Fits all standard sliding doors 1" and 1.5" thick

Lock and Block Sliding Glass Door Gate Features :

  • Patent Pending! Only sliding glass door gate available on the market today!
  • Securely clamps onto the functional panel of a sliding panel door.
  • Helps reduce the risk of injury to your infant or pet, as well as damage to your sliding screen door.
  • Safety gate swings open in both directions, allowing easy entering and existing.
  • Use gate and screen door simultaneously
  • Steel construction
  • Gate swings open in both directions
  • 1 year manufacturer against warranty defects.
  • Gives visibility to sliding doors so child does not run into the sliding door.
  • Along with parent supervision, parents can feel comfortable leaving the sliding door open allowing the fresh air to circulate.
  • Can also be used as a pet gate.
  • Color: White gate with gray hardware.


Questions and Answers:

  •  Will the Patio Door Guardian work on all Patio Doors? This lock is designed to work on all inside sliding Patio Doors.
  •  Will the Patio Door Guardian secure my Patio Door from intruders?This lock is designed to keep your patio door closed and though it does have security benefits it does not lock with a key. It will deter intruders as significant force would have to be used to penetrate the door.
  •  When I mount the Patio Door Guardian to my patio door, how do I determine where to put the screws? You must mount the screws away from the edge of the glass on the sliding door, so you do not break the glass. Do not rely only on the location of mounting plate holes provided with your Patio Door Guardian instructions. Hold the lock up to the desired height and mark your mounting holes away from the glass edge of the door.

I would look at other options for sliding closet doors unless your doors are solid and white. One option would be the Window Guardian Window Stoppers, 4/BOX which are removable suction cups that can stop sliding closet doors as well as windows to keep kids out. These would have to placed in at least two places per door to keep the door from sliding.

Thank you for your question.

Sincerely, Barbara

Window Stops Fit Inside Window Frame or On Windows or Sliding Doors to Limit Opening

by Barbara 18. April 2011 10:44

Question about options to window guards.

Q: "We have a cottage. Our windows are single hung and sliders. We want to keep windows open for ventilation without the expense of window guards. What window stops do you suggest that don't require hiring a handyman? Thanks. Bethany."

Answer: Safe Home sells 4 different types of window stops. The Window Guardian Super Stopper, The Window Wedge, The Window Warden and the Window Guardian Lock. The best choices still are window guards. The John Sterling Window Guards can be locked with a removable lock and swing open for cleaning windows. These are not expensive but would require a handy man type person if you cannot do the installation itself. The Guardian Angel window guards are much easier to install. They are not lockable but do remove completely from the window mounts.

Window Guardian Super Stopper The fastest and easiest to install is the Window Guardian or Super Stopper window stop. This home safety device combines a 2.75 inch flexible suction cup with a unique shaped wedge (1.25 inch x 2 inch). Clean the window. Open the window 4 inches or less. Suction cup on the stops on either side of the single hung window lock mechanism or along the sides of the sliders (as high as you can). These are also great to limit sliding door openings if you have children you want to keep inside the house.

Window Wedge: The next easiest to install is the Window Wedge®. The Window Wedge® uses two 8 inch velcro strips that are 3/4 inches wide. The wedge portion is removable so you can open the window opening wider for cleaning. The that fit on the window frame itself. Made in USA.

To Install Window Wedge Window Stoppers On a Double Hung or Single Hung Window:

    Close the window
    Clean the surface of the window trim prior to application. Do not attach to glass itself.
    Peel off the backing from the 8 inch loop strip and place in the center of the upper window frame for a double hung or single hung window.
    Attach the Window Wedge® to the loop strip.
    Attach the second window wedge on the other side at the same height.
    Open the window until it is stopped by the window wedge.
    Note: For maximum child safety, maximum window opening should not exceed 4 inches.

To Install Window Wedge Window Stoppers On a Slider Window:

    Close window. Clean window frame surface before application of loop strip.
    Peel off backing of 8 inch loop strip and place in center of upper horizontal window frame (not on the glass)
    Attach the Window Wedge® to the loop strip with the
    two tines facing the adjacent window section.
    Slide window open until contact is made with the Window Wedge®
    Attach the second Window Wedge® unit to the bottom part of the
    Adjust the position of the Window Wedge® so that the
    window opening is 4 inches or less.
    Note: For maximum child safety, maximum window opening should not exceed 4 inches.

Window Guardian Window Lock. The push-button key lock design is a patented feature. Remove the key to keep the window locked. Easy to use, this security lock provides peace of mind and installs easily in minutes. The Window Guardian has a tamper-resistant cover and fits most windows. Requires a screwdriver for installation. White.

Before installation, remove the pull-key and cover.

1. Push the button while pulling the pull-key until it comes free. To remove cover, push down and slide it along the base towards the pull-key end.

2. Place the base on the spacer and line up the screw holes. Using the three #6 at head wood screws attach the base to the window or sill so that the end of the base is close to the edge of the sill or window.

3. Place the pin body onto the base so that the location tab ts into one of the three position slots. Select the position slot that gives the closest t to the keeper without causing interference.

4. Slide the cover along the base from the pull key end until it snaps into place. If it seems to bind, turn the cover around to position the locking bump at the correct end.

5. Place the pull key into the back of the assembled body and rotate gently until it finds the correct alignment and push the button, locking it in place.

6. Locate the keeper and install with the two #6 pan head screws. Clip the cover over the keeper to hide the screws. (Fig 3) An alternate orientation of keeper for vertical mounting is supplied. Use the second keeper as a holder for the pull-key when not engaged in the lock.

7.For aluminum windows, fit the lock to the aluminum adapter with 3 #6 machine screws. Fit the aluminum adapter to the handle or the flange at the end of the window. Secure the adapter with 2 Allen screws with Allen key provided. Use the appropriate keeper or drill a hole in the sill when required.

How to Use the Window Guardian: To unlock, pull the Pull-key and rotate 90 degrees/ the key button does not have to be pressed. The Pull-key can be left in. To remove the Pull-key, press the Pull-key button and pull until the key pops out. A second keeper is supplied as a location to store the Pull-key when not engaged in the lock. To insert the Pull-key into the key hole, rotate the key gently until it slides into alignment with the key hole. Once aligned, press the key button and push the key further into the key hole until you hear a click. Additional holes or keepers can be used to create locking positions that allow for partially open windows. Made in China.

The Window Warden fits in the window track of a double hung, single hung or slider or sliding door or on the window trim that surrounds the glass. Each Window Warden™ Kit Bulk Pack contains:

 

  • One mounting bracket 2 7/8 inches long with two 1/2 inch key hole openings plus two openings for mounting screws (included)
  • One Window Warden Unit (plastic) 2 inches long, 7/8 inches wide and 5/16 inches thick. This mounts onto the bracket using two plastic tab that fits onto the mount using "keyhole" openings on the bracket 
  • Three screws
  • One round stop button for use if unit is mounted onto the window frame. (not required if mounted within the window sliding track.
  • Installation instructions. To lock the Window Warden, push in the side button lock pin or slide the stop button on the top of the unit. To release, move the mechanism on the top of the unit away from the window glass.
Note: None of these products are substitutes for adult supervision. Never leave a child unattended with an open window. Thanks for your question

 

Sincerely, Barbara

Childproofing Slider Windows

by Barbara 2. May 2003 15:52

Question about window guards for a wide, tall sliding window.

Q: "We have large, sliding windows. One side of each window slides horizontally. The inside measurement (ie, the actual "screen" itself - this measurement does not include any window framing, etc) of the screens are: 61" high, 30" wide. I want to be sure to purchase the correct window guard. Do we have to cover the entire opening of the screen? That seems excessive to me. I was thinking that the guard would need to come up as high as a standard safety gate would - but maybe I am wrong. Please let me know if you have what we need. Sincerely, Kimberly"

Answer:
Dear Kimberly,

To childproof a slider window or a casement (wind out) window, the only safe way is to cover the entire window opening with one or more vertically mounted guards spaced side by side with a 4 inch or less space between them. Yes, this means the guard looks like prison bars. Otherwise a child could use a horizontally installed guard as a ladder and climb over the guard and fall out. In order to slide both sides of your window, you will need to stack guards side by side to cover the entire window. To determine the size that you need, please go to our window guard sizing and selection page.

There was a sad situation in New Jersey a few months back. A child fell OVER a horizontally mounted window guard through the screen. It was a slider window. I was contacted by a man who was going to testify about this tragedy. Horizontal window guards are made for single hung or double hung windows: a window stop can be used to stop that window from opening above the guard so the child cannot climb over. Sometimes, parents will protect the entire window if it is next to a bed or sofa where a child might fall against the window and break the glass.

Since this was originally published in 2003, Safe Home has added a second window guard line, the John Sterling line. These are expanding window guards, not telescoping ones. The window guard sizes range include sizes from an 11 inch window guard that expands to 24-42 inches to a 6 bar guard that expands from 58 inches to 76 inches. Some units are fixed ones that can be modified to swing open egress or escape window guards with accessories such as a locking channel for a six bar basic window and a safety release pin to pull out so the window can swing open.

Feel free to contact us if you have additional questions or want to childproof a number of windows in your home.

Sincerely, Barbara