Safe-Home.com

Healthier Living | Child Safety | Eco Friendly Tips

Stop Under Sink Water Leaks With Floodstop Water Valve Unit for Hot and Cold Water Lines

by Barbara 22. July 2012 07:01

Question about the FloodStop for Sinks Lead Free Water Valve FS3/8CD.

Question: "Our neighbor recently had extensive water damage from a leak under a bathroom sink. The sink is in a rarely used bathroom. The first hint of the water leak was the damp spot on the ceiling in the room below. What product do you suggest for protecting our guest room sink which is rarely used? Thanks. Sam."

Answer:  For a single location, install the FloodStop for Sinks Lead Free Water Valve FS3/8CD. The "CD" stands for compression fitting, i.e. no soldering is required. The Floodcheck water valves connect to the angle stops and supply lines. FloodStop water valves are full port ball valves that meet the California and Vermont lead free water valve standards for drinking water.  Add additional sensors for more coverage under the sink. Do remember that you will need an unswitched electrical outlet for power: electricity is used only when the sensor detects water.

When a hot or cold water leak is detected, Floodstop shuts off the water below the sink and sounds an 87 db alarm.

Installation:

    Connect the water valve to cold and hot water lines under the sink.
    Mount the control unit.
    Place sensor(s) on floor.
    Plug power supply into an unswitched outlet. Note: electricity is used only when the sensor detects water.

NOTE: DO NOT PLACE SENSOR DIRECTLY ON METAL PAN OR DAMP FLOOR. If no water is present and alarm sounds, place paper towel or cloth under sensor to "insulate" against floor dampness or metal of pan. When the paper or cloth gets wet, the sensor activates the shut-off and sounds the alarm.

How FloodStop (FS 3/8-CD) Works:

    FloodStop valves connect to the angle stops and supply lines.
    Water leak sensor is placed at the base of the fixture (sink, laundry tubs, bathtub, etc.).
    Valve remains open until a water leak or water loss is detected.
    Water on the sensor signals the Floodstop controller which closes the valve and alarms.
    Valve remains closed until system is reset, and sensor is dry.

FloodStop (FS 3/8-CD) Components:

    Motorized Ball Valves (Two Valves, 3/8 inch Compression Fitting).
    Control unit with battery backup (4 C batteries, not included).
    AC power adaptor (or use 4 C Batteries as primary power source).
    Water leak sensor (1.25" X 7.5").
    Output contact wires (2).

Technical Specifications:

    UL Listed Class 2 Wall Adaptor, 115AC/9VDC.
    UPC listed, full port, motorized ball valves.
    Motor operates at 6VDC.
    Rated 0-180 PSI. Max 250 PSI. Solid brass.
    Signal outputs: 2 normally closed.
    Alarm: beeping with mute button.

Features:

    For added water detection protection, add more sensors. Sensors plug into sensors, NOT the Control Box.
    The 3/8 inch valve is 3.75 inches long.
    Controller has reset and test buttons to test valve performance plus battery back up.
    Easy to install, operate, and maintain.
    Designed for residential, condo and apartment dwellings.
    Full port ball valves automatically shut off water supply to sink when water sensor/sensors get wet.
    Power: 120VAC and/or battery backup (4 C batteries).
    No wires to route throughout the home.
    Alarm: beeping with mute button.
    Water Sensor: 1.5" X 7.5", double sided. Additional sensors may be added in series.
    AC Adapter Cord Length: 6 Ft.
    Wire Length from the Controller to the Valve: About 30 Inches Long.
    FloodStop Controller:
        3 buttons: Mute, Close Valve and Open Valve.
        Water sensitivity adjustment. Clockwise: less sensitive. Counter clockwise: More sensitive.
        4-pin connection to valve/sensor connector.
        Outputs: Normally closed. Contacts for any device that can utilize them, like auto phone dialers, alarm systems, X10 home automations devices.
    One year limited manufacturer warranty.

I hope this helps with your situation.

If you want whole house protection, a install the Floodstop Whole House Auto Water Valve System. This unit comes in 3/4”, 1” and 1.25” valve sizes. Included with each system are one Motorized Full-Port Ball Valve,one Controller (that shuts off the main water valve),four Sensor Modules, four sensors to place in areas you want protected, one transformer for the controller and four low voltage transformers for the sensor modules. This unit screws onto the water pipe, i.e. it is an NPT or National Pipe Thread Tapered Thread.

Go to WWW.SafeHomeProducts.com for more information.

Thank you again.

Sincerely,

Barbara

FloodStop Automatic Water Valve and Alarm for Dishwasher, Toilet or IceMaker

by Barbara 12. July 2010 22:59

Question about the Floodstop 3/8 Inch Automatic Water Shut-Off and Alarm.

Q: "Water is seeping through the floor under my dishwasher. Right now there is just a small wet spot. My basement is to be finished this winter so I want to protect the house from water leaks from the dishwasher, toilets, etc. if I can. I see that you have a device that would shut off the water to the dishwasher and sound an alarm if the new dishwasher (to be installed soon) leaks in the future. How complicated is it to install the valve? What other units are available? Thanks. Tom"

Answer: My suggestion is to have the appliance store deliver the new dishwasher and have their plumber install the Floodstop at the same time. Check your local tax laws. Currently, at least in Iowa and in Pennsylvania, you don't pay sales tax on the appliance if the store delivers the unit and does the installation. Depending upon your locale, the additional plumbing charge may be $50 and up. The protection is worth it.

Most dishwashers are next to a sink since they use the sink drain. The plumber would install one or more water sensors on the floor where the dishwasher will be placed (we recommend a minimum of two), the water valve, attach the alarm valve turn off unit to the wall (probably under your sink), and plug in the unit. The sensors should be tested by wetting them. After they are dried and the water valve is reset, then the dishwasher is installed.

The FloodStop unit for dishwashers and toilets has a 3/8 inch compression valve that connects to the angle stop and the supply line. You do need electricity unless you plan to change batteries at least once per year. (The unit draws power only to open or close the valve.) For AC, use the 4 C batteries, not included, as back-up. Contacts allow the option of connecting to phone dialers, alarm systems, X10 home automation devices, etc. There is also a 9 foot controller valve extension cord available to allow mounting of the controller in a more or less visible location. The length of cord included with Flood Stop leak detection alarms is 2.5 feet.Transformer extension wires are also available.

We also sell Floodstops for water heaters, washing machines that does not require a plumber, sinks, icemakers with 1/4 inch lines etc. All units have a one year warranty by the manufacturer. We've had customers literally saved from flooded homes from these units especially from leaking washers and water heaters.

Floodstop Dishwasher, Toilet and Ice Maker Unit Information:

* The FloodStop valve is connected to the angle stop and supply line

* Water/leak sensor is placed at the base of the appliance or fixture (Dishwasher; Sink; 3/8" Icemaker; Toilet; etc.)

* Valve stays open until water loss is detected

* Water on sensor closes FloodStop valve and sounds alarm * Valve stays closed until problem is attended to and system is reset

FloodStop 3/8 Inch Water Valve and Water Alarm Components:

1. Motorized Full-Port Ball Valve (3/8" Compression).

2. Control Unit with Battery Backup (4 C batteries, not included).

3. AC Power Adaptor (or use 4 X C Batteries as Primary Power Source).

4. Water Leak Sensor.

5. Output Contact Wires (2).

Thank you for your question.

Sincerely,

Barbara

FloodChek Hoses and FloodStop for Washing Machines

by Safe Home Team 11. September 2009 12:15

Barbara discusses the FloodChek washing machine hoses and the FloodStop automatic water shut off valve system for washing machines. The FloodStop system with water alarm and water sensors alerts of washing machine leaks. Easily installed, the rupture proof washer inlet hoses plus the FloodStop prevent or stop water leaks from causing water damage. 24/7 protection from leaking washing machines or leaking hoses.

Shutting Off the Flood Stop for Water Heaters Remotely

by Barbara 21. June 2008 03:12

Question about the product:
FloodStop 3/4 in Valve Water Heater Shutoff COMPRESSION Product Code: : FS-3/4-C .

Q: "It looks like your system has a control box with buttons. Can I turn the system off or on with this controller placed remote from the shutoff valve? I would like to be able to turn the whole water supply off when I am away." -Kevin

Answer: The FloodStop controller must be placed near the hot water heater. The only extension wires available are for the AC adapter.

Yes, you can turn the system on and off remotely. The FloodStop Controller indeed has three buttons, mute, close valve and open valve.The outputs are normally closed. You can use contacts for any device that can utilize them, like auto phone dialers, alarm systems, X10 home automations devices., etc. There is a 4-pin connection to valve/sensor connector.

We do sell a whole house water shut off device, the WaterCop , that has a remote shut-off option. That unit is installed on the main water valve into the house. Water sensors are placed under or near appliances such as water heaters, washing machines, dishwashers, water dispensing or ice making refrigerators, etc. The remote shut off can be placed anywhere you please as long as it can be connected to the Watercop controller with Cat 5 cable.

Please contact us if you need more information. The manuals for these products are on our website.

Sincerely,
Barbara